• GA Series GA Series
• GP Series GP Series
• A、B Series A,B Series
• DPS Pressure Switch DPS Pressure Switch

Feature description

The installation and application of the filter

1.Before installation, the sundry granule such as dust, oil pollution and chipping in pipeline shall be cleaned up to prevent the mixture of fragments of

   seal materials.

 

2.Never install reversingly the direction of intake and outlet. It shall be installed vertically and the bowl is downward.

   For the convenient ofmaintenance, proper space around the device shall be left. Theinstallation height of filter shall accord with the elevation that

   the filter bowl can be dismantled.

                 

 

3.Never install the device mear the air compressor. It shall be installed next to the pneumatic components at the end of

   pipeline, since the water and oil in the compressed air with high temperature from air compressor take on gaseous

   state which will not only influence the filter effect, but are easy to damage the seals. Please install condenser and

   dryer in front of the filter.

 

 

1.To prevent the external force to damage the filter bowl, never install it in the side of access of delivery vehicles or a protection barrier may be built.

 

2.The drain bowl is made of polycarbonate which can not be used in the environment with synthetic oil, organic solvent, chemicals, cooling fluid, alkali

   and acidic matter, gluewater; and the site additive with the above matters. Meanwhile, the direct sunshine shall be avoided.

 

3.Regular draining of bowl shall be conducted. Once water level surpasses the breakwater, the sewage filtered will be carried to the output compressed

   again, causing secondary pollution.

 

4.To gusrsntee the filter effect, the filter core shall be cleaned or changed regularly.

 

5.Please regularly examine whether the plastic drain bowl has crack, damage or other aging.

 

The installation and application of oil feeder

1.The direction of intake and outlet shall not be installed reversingly. Before installation, the sundry granule such as dust, oil pollution and chipping in

   pipeline shall be cleaned up to prevent the mixture of fragments of sealmaterial.

 

 

2.It will be difficult to supply oil and conduct maintenance if the Lubricator is set too high.

 

3.Lubricator shall be installed after the air filter and Regulator to prevent moisture entering the oil bowl and avoid oil emulsification. The throttle orifice in

   Regulator shall not be polluted by oil and the rubber parts shall not be influenced by oil mist. It is good for the atomization of that the velocity of low

   after Regulator is higher than that in front of the valve.

 

                    

 

4.The number in dial in adjustment ring of Lubricator shows the position of oil quantity adjustment.

   The larger the number is, the more the oil dripping is. It is not for oil drops.

 

5.When Lubricator works, if there is a part in the pipeline loop that can not be supplied with oil, this

   part shall be set with one-way valve to prevent reflux.

 

6.The air flow that is used by Lubricator must meet the requirement of necessary quantity of oil dripping

   (minimal flow for mist). The insufficient air flow will cause the failure of oil dripping.

 

7.The Lubricator can be added oil under pressure. When oil is added, the oil-fill plug shall be slowly opened and dismantled after the pressure in oil bowl

   has been completely eliminated to prevent oil-fill plug flying off or oil spraying.

 

8.The oil level in oil bowl shall stay between the up limit and down limit, and please supplement oil on a timely basis：

  ◆Method for supplementing oil

   When Lubricator is supplemented with oil, the oil-fill plug shall be turned off. Turbine oil poured into the oil bowl shall reach 80% of its volume.

   Oil shall be regularly examined and supplemented to allow the device to work under the situation that oil is sufficient.

   (As when the oil level is under the oil suction pipe, it can not supply oil for the system. Therefore, the oil shall be supplemented before the bottom of

   oil suction pipe is exposed).

  ◆Oil quantity and its adjustment

   Generally speaking, the free air of each 10m³ used 1cm³ as the benchmark oil supply quantity.

  ◆Lubricant

   The Lubricant that is recommended for pneumatic components is one kind (ISO VG32) of turbine oil. Especially when pneumatic components are

   lubricated, its particularity shall be considered. Lubricant shall be anti-rust and avoid swelling, shrink and deterioration of seal materials (pneumatic

   components mostly adopt NBR as the seal's material). In addition, the performance of oil dripping of lubricant shall be considered. The viscosity that

   is too high or too low is not proper.

 

9.Please regularly examine whether the plastics bowl and inspection window of Lubricator have crack, damage or other aging situation.